IBM i Support: Software Technical Document : 19145254

Document Title
Getting Support for Form Types in a Remote Output Queue (RMTOUTQ)

Document Description
When printing operating system spooled files to a LAN attached printer using a Remote Output Queue (RMTOUTQ), you will not normally receive message CPA3394 – Load form type ‘&4’ device &5 writer &1 when the form type changes.

Getting Support for Form Types on One or More Remote Output Queues

Remote writers can support form types; however, you must start the writer with the message option set to *INQMSG (so you get an inquiry message whenever the form type changes) or change the writer after it has started. To start the writer with form type support, use the following operating system command:

STRRMTWTR OUTQ(remote-outq-name) FORMTYPE(*ALL *INQMSG)

To change an existing writer to have form type support, use the following operating system command:

CHGWTR WTR(remote-outq-name) FORMTYPE(*ALL *INQMSG)

After you have done either of these, you will receive message CPA3394 – Load form type ‘&4’ device &5 writer &1 in the writer’s message queue whenever the form type changes. However, if the writer ends and restarts automatically or manually without specifying FORMTYPE(*ALL *INQMSG), you will no longer receive message CPA3394.

Getting Support for Form Types on All Remote Output Queues

To get form type support on all of your remote output queues each time they are started, you can change the Start Remote Writer (STRRMTWTR) command to specify FORMTYPE(*ALL *INQMSG), rather than FORMTYPE(*ALL *NOMSG). That way, you will get form type support unless the STRRMTWTR command is specifically overridden to not support form types. This can be done by copying the command to another library that is higher in the library list than QSYS and then bby using the following operating system command:

CHGCMDDFT CMD(cmd-library/STRRMTWTR) NEWDFT('FORMTYPE(*ALL *INQMSG)')

Note: You can use the Change Command Default (CHGCMDDFT) command on the STRRMTWTR command that is in library QSYS, but there are two potential dangers with this, namely:

1. If you install a newer version of the operating system or reinstall the current version of the operating system, your changes to the STRRMTWTR command will be replaced by the settings as shipped by IBM.
2. If you make an error when changing the command defaults for a command, you can cause that command to fail every time it is run. Therefore, in this case, you might not be able to get remote writers started again without changing the command defaults back or restoring the STRRMTWTR command from your installation media.

Note: Another option is to use the LPR Print Driver (TSPLPRD) utility in a *LAN 3812 device description. This is an unsupported utility that provides the function of sending spooled files from an output queue to an ASCII printer that is attached to an LPD server. This is a similar function to what is provided using Remote Output Queues (RMTOUTQs), but it differs because this driver exit program is specified on a printer device description. Thus, it can make use of information specified about the printer in the device description that is not available on a remote output queue. Also, because it uses LPR within a printer writer, it supports page ranges, multiple copies and form types, yet it can be used with any printer that currently uses a RMTOUTQ including dot matrix and line printers.

For additional information on using the LPR Print Driver (TSPLPRD) utility, refer to the following Rochester Support Center knowledgebase document:

18762910, Configuring a *LAN 3812 Device Description that Uses the LPR Print Driver (TSPLPRD) Exit Program: Database 'Rochester Support Line KnowledgeBase', View 'All Documents', Document 'Configuring a *LAN 3812 Device Description that Uses the LPR Print Driver (TSPLPRD) Exit Program'

For additional information on the capabilities and limitations of RMTOUTQs and *LAN 3812 printer device descriptions, refer to the following Rochester Support Center knowledgebase documents:

14143423, Capabilities and Limitations of Remote Output Queues (RMTOUTQs): Database 'Rochester Support Line KnowledgeBase', View 'All DocumentsAll Software', Document 'Capabilities and Limitations of TCP/IP Remote Output Queues'
412453666, Capabilities and Limitations of *LAN 3812 Printer Device Descriptions: Rochester Support Line KnowledgeBase

Notes

Leave a Reply

Your email address will not be published. Required fields are marked *